Showing posts with label noise. Show all posts
Showing posts with label noise. Show all posts
9/4/08
Why the spekaer emit noise?
To analyze the usage, there are a few reasons explain why the speakers emit buzz sound or noise:1. Speaker is a passive component, and the drive circuit decides the sound. Therefore, giving the correct power and waveform to the speaker is the basic request.The too large power will lead to the too big amplitude of the diaphragm. The slight problem is distortion, but the serious problem is that the diaphragm might hit the mechanism or the magnet and cause the buzz sound. The basic waveform to drive the speaker is sine wave, if we give square wave or other waves, the efficiency of the speaker will reduce and easily get heated, the buzz sound may happen as a matter of course.2. The enclosure design of the product will also affect the quality of the sound. The well designed enclosure can improve the frequency response curve of the speaker.The area of sound apertures of the enclosure at least request over 1/8 area of the surface. We need to keep enough vibration space between the case and the diaphragm to avoid the diaphragm hitting the case when it works and emits the noise.
3/27/08
The Noise Reason of Electret Condenser Microphone
The noise of an electret condenser microphone mostly comes from:
1. Impure current source
If the direct current mix with the alternating current signal, we will hear a stable level, low frequency and continual noise. We can lead the power to the microphone directly, or set a non-join circuit to filter the AC signal to improve the situation.
2. Mechanism design
The faulty mechanism design might cause the wind sheer sound or resonant sound. Normally a deep curved sound hole is good to prevent the ESD, but it has some bad influence on the sound; for example, it is good for some frequency but some other frequencies might be declined. Therefore we may get unnatural sound with buzz or noise.
3. The noise from signal
Microphone is a component to receive sound, which can receive wider frequency range than human ears. Both high and low frequency signal will transform into noise as a form of harmonic waves after being received. An obvious example is that the noise happens when the cell phone and the blue tooth are set too closely. Therefore when we design the microphone circuit, we should keep it away from the antenna or other components which might radiate signal.
4. Outer noise
Generally, the main noise is the sound of the wind. The users complain about the unclear sound because the higher join capacity receives the sound of the wind or breath. Modifying the join capacity (normally around 0.022~0.1 u) can solve this problem.On the other hand, if the outer sound (exclude the main sound) is too louder, it means the sensitivity of the microphone or the loading impedance is too high, what we can do is change to a low sensitive microphone or to decrease the loading impedance.
1. Impure current source
If the direct current mix with the alternating current signal, we will hear a stable level, low frequency and continual noise. We can lead the power to the microphone directly, or set a non-join circuit to filter the AC signal to improve the situation.
2. Mechanism design
The faulty mechanism design might cause the wind sheer sound or resonant sound. Normally a deep curved sound hole is good to prevent the ESD, but it has some bad influence on the sound; for example, it is good for some frequency but some other frequencies might be declined. Therefore we may get unnatural sound with buzz or noise.
3. The noise from signal
Microphone is a component to receive sound, which can receive wider frequency range than human ears. Both high and low frequency signal will transform into noise as a form of harmonic waves after being received. An obvious example is that the noise happens when the cell phone and the blue tooth are set too closely. Therefore when we design the microphone circuit, we should keep it away from the antenna or other components which might radiate signal.
4. Outer noise
Generally, the main noise is the sound of the wind. The users complain about the unclear sound because the higher join capacity receives the sound of the wind or breath. Modifying the join capacity (normally around 0.022~0.1 u) can solve this problem.On the other hand, if the outer sound (exclude the main sound) is too louder, it means the sensitivity of the microphone or the loading impedance is too high, what we can do is change to a low sensitive microphone or to decrease the loading impedance.
Subscribe to:
Posts (Atom)
